• Universal Input (T/C,RTD,Linear Input) and ranges.
• 24V DC power supply for 2 wire transmitter.
• High Accuracy.
• Self Diagnosis Function:Input fails safe operation.
• Multiple level keyboard locking function.
• Adjustable PV offset.
• Input /output programmable..
• PID auto tunning or fuzzy control
• Manual auto switching bump less.
• Up to four alarms in 17 modes.
• Remote set point.
• Program controller 8 patternsX16 segment/1patternX129 segments.
• Switching power supply: 85-260VAC,50 Hz or 24VDC.
• Modular based output cards.
• Heat cool,VMD,PID control output.
• NPL traceable certificate.

Input Signal	Temperature	Thermocouple	S,B,T,R,K,E,J,N,W	Input drift:< 1micro V/ohm leads resistance
			Sensor Break Protection	Internal cold junction comp.:0-50 degC.
		RTD	Pt-100,Cu-100,Cu-50	Max. lead resistance: 100 ohm per lead.
			Sensor break protection
	Voltage	20-20mVDC,-100-100mVDC,0-100mVDC,0-500mVDC			Max. lead resistance:100 ohm
		0-100mVDC,0-5VDC,1-5VDC,0-10VDC
Input filter time:0-20 sec-Input impedance for current signals: 5 ohm; Input impedanc for other other signals:>600 kilo ohm.
Accuracy	For linear Input	0.2% FS
	For Temperature Input	0.2% FS+_2.0 deg C	For B type of Thermocouple,may be more than 0.2%FS in the range of 0-400 deg C		Cold junction compensation accuracy +_2 deg C
Control modes	ON/OFF Control PID,P,PI or PD control	Control cycle time:1-100 sec. Single action,reverse action head control or direct action cool control	Double action, heat/cool control Positive/negative rotation control for position-proportion type of instrument
Output Signals	Linear current	0-20mA,4-20mA (max. load : 500ohm) 0-10mA (max. load :1kilo ohm)	Accuracy:+-0.3%FS
	Relay	250VAC or 30VDC/1A for resistive load
	SSR driver	Von=13+-VDC(30mA max.),V off=0.1VDC
SCR trigger	Zero-crossing trigger or phase shifting trigger output for 1-2 or 3 phase SCR		500A,upper power triac,or 2 inverse parallel SCR power modules.
Event input/output	Event Input	RSV/LSV selection,A/M switching,SV selection	Passive contact,min holding time on or off should be 200ms
	Event output	PV alarm,A/M state		Relay contact
Power output	Isolated 24VDC/30mA power output
Retransmission	PV,SV,OP1,OP2, or valve position selectable to be transmitted programmable
Communication	RS232 (single instrument)				RS485(max. 99 instruments)
Display	PV	4-digit red LED	Display resolution:0.001,0.01,0.1,1
	SV	4-digit green LED	Display cycle time:0.5sec
	Light Bar	20 segments of red LED	Display range:measuring range(-10%+10%)
Protection	Automatic reset when operating abnormally		Error code indication		Multiple alarm type
	Multilevel parameter safety protection		Parameter are stored for an unlimited time
Operating conditions	Power supply:100-240VAC(-15%+10%)50/60Hz or 24VDC(-15%+25%),6W max.
	Temperature:0-50degC, Relative Humidity:5-85%RH(non condensing
Storage conditions	Temperature:-25-70degC.
	Relative Humidity:5-95% RH(non-condensing)

• 1. Data Acquisition- It can capture high-quality measurements on many channels, at high data rates
• 2. Integrated System- It use Channel Architecture technology to unify signal flow from sensors to software for large systems.
• 3. Double output temperature control system.
• 4. 3-phase SCR zero crossing/phase shifting control system.
• 5. It is used for cascade control system.
• 6. It is is also used in Position-proportion control system etc.